Vestil PLID Manuel d'utilisateur télécharger pdf

Revised 09-07

A company dedicated to solving ergonomic and

material handling problems since 1955

VESTIL MANUFACTURING CORPORATION

2999 North Wayne St., Angola, IN 46703

Phone (260) 665-7586 • Fax (260) 665-1339

E-mail: [email protected] • www.vestil.com

POLY LID INSTALLATION

D- AND H-STYLE SELF-DUMPING HOPPERS

INSTRUCTION

GUIDE

Fork Truck Attachments

H-Style Hopper lid bracket installation ............ 2

D-Style Hopper lid bracket installation ............ 3

Installing the hopper lid ............................... 4-5

Contents

Warnings and Safety Instructions................ 1

Replacement Parts and Receiving .............. 1

Required Tools and Time ............................ 1

WARNINGS & SAFETY INSTRUCTIONS

• Ensure that all employees understand and follow

the following instructions.

• Failure to read and understand these instructions

before installing the lid constitutes a misuse of

the product. All persons involved in performing this

task must be familiar with this material.

• ALL contents must be removed from the hopper before

any work is performed on the hopper.

• Ensure that all information/safety/warning labels stay

in place and remain legible.

• Maintenance and repairs are to be done only by

personnel qualified to perform the required work.

Consideration will not be given for warranty repair

charges without prior written authorization from the

manufacturer.

REPLACEMENT PARTS

We take pride in using quality parts on the

equipment we manufacture. We are not responsible for

equipment problems resulting from the use of unapproved

replacement parts.

RECEIVING INSTRUCTIONS

To order replacement or spare parts for this

equipment, contact the factory.

In any communication with the factory please be

prepared to provide the hopper’s serial number, which is

indicated on the hopper’s dataplate.

It is possible that this replacement part could incur

damage during transit.

Inspect the parts and packaging closely when it

arrives.

If you see evidence of damage or rough handling to

either the packaging or to the part when it is being received,

immediately make a note of it on the packing slip!

It is important that you remove the part’s packaging

upon its arrival to ensure that there is no concealed damage

or to enable a timely claim with the carrier for freight damage.

Also verify that the part and its specifications are as

ordered.

REQUIRED TOOLS AND TIME FOR

REPLACEMENT

• Pliers (to install “R” clips)

• Tin snips

• Time Required: approximately 10-15 minutes.

D-STYLE HOPPER WITH

POLY LID INSTALLED

H-STYLE HOPPER WITH

POLY LID INSTALLED

1 2 3 4 5

INSTRUCTION 1

Résumé du contenu

Page 1 - INSTRUCTION

1Revised 09-07A company dedicated to solving ergonomic andmaterial handling problems since 1955.VESTIL MANUFACTURING CORPORATION2999 North Wayne St.,

Page 2

2H-STYLE HOPPER LID BRACKET INSTALLATIONNOTE: Retrofit lid brackets can be welded or bolted on. If bolting on, holes will need to be drilled in thehop

Page 3

3D-Style hopper shown with lidand lock bar installed.Front lock bar brackets.Install front lock bar bracket 6” from front ofchute and center on chute

Page 4

The geometry of the lid should allow it to fit inside all 4 brackets, but it might be necessary to cut small notches out of the lid for it to fit pro

Page 5

5Slide pin into hinge bracket.(Side of pin withoutstop pin.)Stop pin.Installed hinge pin.Push stop pin away from bracket. When pin clears bracket, pus

Commentaires sur ces manuels

Pas de commentaire

Vestil PLID Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Équipement Vestil PLID. Vestil PLID User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Équipement Vestil PLID